easypoint tm N40P107 single module (without ic, with push button) www.ams.com revision 1.6 1 - 8 1 general description easypoint? N40P107 is a miniature joystick module concept based on contact-less, magnetic movement detection. the two-dimensional linear encoder ic as5013 is mounted on the bottom side of the application?s pcb, and monitors the movement of the magnet incorporated into the knob and provides directly the x and y coordinates via i2c output. an integrated mechanical push button built in the module provides a ?select? function. figure 1. N40P107-xxxxx-h 2 key features ?? small form factor ?? lateral magnet movement radius up to 1mm ?? direct knob force feedback ?? push button output ?? smd mounting 3 applications the easypoint? N40P107 in combination with the as5013 is ideal for small form factor navigation user interfaces in battery driven portable devices, such as - mobile phones (especially for gaming), remote controls, gaming consoles, analog joysticks(360 degree), mp3 players, pdas, pnd, mid and gps 4 benefits ?? high reliability due to magnetic contact-less sensing ?? easy to use and fast integration figure 2. typical application diagram ep tm module footprint main board (pcb) as5013 (ic) N40P107
www.ams.com revision 1.6 2 - 8 easypoint tm N40P107 datasheet - electrical characteristics 5 electrical characteristics 5.1 mechanical specifications 5.2 electrical specifications 5.3 environmental specifications table 1. mechanical specifications parameter note number of operating shafts single shaft shaft material lpc housing material lpc & pa46 shell material stainless steel or copper alloy travel (xy operation) 1.00mm (10%) travel (z push operation) 0.22mm (0.05mm) directional operating force (xy direction) 0.35n (0.10n) or 0.55n (0.15n) push operating force (z direction) 1.80n (15%) vibration 10-500-10hz 15 minutes, 12 cycles, 3 axes (total 36 cycles) operating life ? xy direction each direction > 1 million cycles operating life ? push z direction > 1 million cycles shaft strength (xyz direction) > 5.0kgf over force 1.5kgf > 100k cycles table 2. electrical specifications parameter min max unit note contact resistance 500 m norm: eia-364-23 dielectric withstanding voltage 100 vac norm: eia-364-20 insulation resistance 100 m norm: eia-364-21, 100vdc bouncing (on/off) 5 ms rate: 2 times/sec. table 3. environmental specifications parameter note operating temperature range -20 ~ +70oc storage temperature range -40 ~ +85oc humidity non-condensing 5 ~ 85% rh degrees of protection ip 5x
www.ams.com revision 1.6 3 - 8 easypoint tm N40P107 datasheet - electrical characteristics 5.4 recommended reflow temperature profile figure 3. reflow temperature profile notes: 1. do not wash the module! do not use flux cleaner or solder paste remover! 2. maximum 3 passes through reflow oven. 217oc 170oc 140oc 250 ~ 260c 60 sec. max. 60 ~ 120 sec. pre-heating 10 sec. max. soldering time
www.ams.com revision 1.6 4 - 8 easypoint tm N40P107 datasheet - application us ing as5013 2d linear encoder 6 application using as5013 2d linear encoder figure 4. application diagram for further information, please refer to the ams as5013 encoder application note an5013-20: http://www.ams.com/eng%29/products/position-sensors/easypoint-joystick-position-sensor/as5013/technical-documents/easypoint- as5013-downloads
www.ams.com revision 1.6 5 - 8 easypoint tm N40P107 datasheet - package drawings and markings 7 package drawings and markings figure 5. N40P107 dimensions (mm 0.15) figure 6. recommended pcb layout (mm 0.05) & circuit diagram % $ rohs % $ $ ?
www.ams.com revision 1.6 6 - 8 easypoint tm N40P107 datasheet - package drawings and markings figure 7. recommended on casing design figure 8. recommended stencil design for 4 gnd-pads 4 q f f e u f d i % $ $ ? as5013
www.ams.com revision 1.6 7 - 8 easypoint tm N40P107 datasheet - revision history revision history note: typos may not be explicitly mentioned under revision history. revision date owner description 1.0 25 may, 2011 abi initial release 1.1 21 jun, 2011 minor changes on text and format 1.2 19 oct, 2011 rph added logos to package drawings and markings on page 5 1.3 05 jan, 2012 changed logos in package drawings and markings on page 5 1.4 17 jan, 2012 added note to recommended reflow temperature profile on page 3 1.5 19 jun 2012 updated key features on page 1 and figure 4 1.6 19 aug, 2013 updated figure 5 23 apr, 2014 updated link under figure 4
www.ams.com revision 1.6 8 - 8 easypoint tm N40P107 datasheet - copyrights & disclaimer copyrights & disclaimer copyright ams ag, tobelbader strasse 30, 8141 unterpremstaetten, austria-europe. trademarks registered. all rights reserved. th e material herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright o wner. devices sold by ams ag are covered by the warranty and patent indemnification provisions appearing in its term of sale. ams ag makes no warranty, express, statutory, implied, or by description regarding the information set forth herein. ams ag reserves the right to change specifications and prices at any time and without notice. therefore, prior to designing this product into a system, it is neces sary to check with ams ag for current information. this product is intended for use in commercial applications. applications requiring extended te mperature range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-sustaining equipment are specifically not recommended without additional processing by ams ag for each application. this product is provided by ams ag ? as is? and any express or implied warranties, including, but not limited to the implied warranties of merchantability and fitness for a pa rticular purpose are disclaimed. ams ag shall not be liable to recipient or any third party for any damages, including but not limited to personal injury, prope rty damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or consequential damages, of any kind, in conne ction with or arising out of the furnishing, performance or use of the technical data herein. no obligation or liability to recipient or any third party shall arise or flow out of ams ag rendering of technical or other services. contact information: headquarters ams ag tobelbaderstrasse 30 8141 unterpremstaetten austria, europe tel: +43 (0) 3136 500 0 website: www.ams.com
|
